---
title: GPS Markers – DIP and HARP
description: Last updated November 15, 2026 The Stratos stores up to 100 named GPS markers. You can set any marker as the DIP (Desired Impact Point), the HARP (High Altitude Release Point), or both. The Stratos then shows the distance to…
url: "https://deepandsteep.io/knowledge/stratos-gps-markers-dip-and-harp/"
updated: "2026-11-15"
category: Stratos Tactical GPS Altimeter
---

# GPS Markers – DIP and HARP

Last updated November 15, 2026

The Stratos stores up to 100 named GPS markers. You can set any marker as the DIP (Desired Impact Point), the HARP (High Altitude Release Point), or both. The Stratos then shows the distance to the HARP in the aircraft, and navigates you to the DIP in freefall and under canopy.

## Where the DIP and HARP Show

![Stratos GPS screen showing signal strength, the DIP LZ-OSCAR at 5.1 nautical miles, the HARP HARP-X at 4.2 nautical miles, and GPS recording on](https://deepandsteep.io/wp-content/uploads/2026/11/stratos-screen-gps.avif)
GPS screen

![Stratos altitude screen in the climb with a HARP set: ground track 270, ground speed 92, altitude 11.8, Ha 4.2 and Et 4 minutes 32 seconds](https://deepandsteep.io/wp-content/uploads/2026/11/stratos-screen-climb-harp.avif)
In the climb, with a HARP

![Stratos altitude screen in the climb with no HARP set: ground track 075, ground speed 0, altitude 2.34, Lz 4.2 and vertical speed 2950](https://deepandsteep.io/wp-content/uploads/2026/11/stratos-screen-climb-dip.avif)
In the climb, without a HARP

- **GPS screen:** Displays the names of the active DIP and HARP and the distance to each, or **Not set**.
- **In the climb, with a HARP:** **Ha** is the distance to the HARP and **Et** is the estimated time to reach it. The turn direction and distance field also point to the HARP.
- **In the climb, without a HARP:** **Lz** is the distance to the DIP.
- **After exit:** Every field points to the DIP: its distance, the turn to the DIP and the DIP glide. See [Altitude Display Configuration](https://deepandsteep.io/knowledge/stratos-altitude-display-configuration/).

Tip

Before every jump, check the DIP and HARP names and distances on the GPS screen, to make sure the correct markers are active.

## Markers List

From the GPS screen, press the center button, and select **Markers List**. The list is in alphabetical order, with the active DIP and HARP in **bold**. Select a marker to open it. If no markers are saved, the Stratos shows **List Empty**.

![Stratos Markers List in alphabetical order, with HARP-X and LZ-OSCAR in bold](https://deepandsteep.io/wp-content/uploads/2026/11/stratos-screen-markers-list.avif)
Markers List

![Stratos marker menu for LZ-OSCAR: Save LZ-OSCAR, Coords, Name, Mark Here, Delete Marker, Active DIP Yes, Active HARP No](https://deepandsteep.io/wp-content/uploads/2026/11/stratos-screen-marker-edit.avif)
Marker menu

If the list is not in alphabetical order, from the Home screen, press the center button, and select System → Misc → Fix Marker List. The Stratos rebuilds the list.

You can also add markers with the Deep and Steep app. See [Deep and Steep App Overview](https://deepandsteep.io/knowledge/app-ios-android-overview/).

## Adding or Editing a Marker

1. From the GPS screen, press the center button, and select **Add Marker**, or open a marker from the **Markers List**.
2. Select **Name**, and enter the name.
3. Select **Coords** to enter the position, or select **Mark Here** to use your current position.
4. Select **Save** (shown with the marker name) at the top of the menu. If you leave the menu any other way, the Stratos discards the changes.

Note

A new marker starts with the coordinates of the last marker you added.

### Coords

Enter the coordinates by hand, as MGRS (the default) or as Lat/Lon. To choose the format, see [Display Units](https://deepandsteep.io/knowledge/stratos-display-units/).

- **MGRS:** Enter the full 10-digit grid, 5 digits of easting and 5 of northing. Pad a 6- or 8-digit grid with zeros at the end of each half. For example: `552 890` becomes `55200 89000`.
- **Lat/Lon:** Enter decimal degrees with 5 decimal places. Use **+** for north and east, **-** for south and west.

Press the center button to move through every field to the end. If the Stratos shows **Invalid coords** when you save, check the coordinates, and enter them again.

If you only have a street address, or lat/lon in another format, use an online GPS coordinate converter.

### Name

Enter up to 10 characters: letters, numbers, “-” and spaces. A marker saved with no name gets a number as its name, such as `0007`.

### Mark Here

![Stratos Mark Here screen with Cancel and Save, the current position 17R LL 55234 89012, Alt MSL 39 and 9 satellites](https://deepandsteep.io/wp-content/uploads/2026/11/stratos-screen-mark-here.avif)
Mark Here

Mark Here uses your current position. The screen shows **GPS Search...** until the GPS has a fix, then your position, the altitude above sea level (**Alt MSL**) and the number of satellites (**Sats**).

Select **Save** to copy the position into the marker, or select **Cancel** to leave it unchanged. This Save copies only the position. To save the marker, select Save at the top of the marker menu.

- Stand in a clear area with nothing overhead within 20 ft. See [GPS Signal Best Practices](https://deepandsteep.io/knowledge/gps-signal-best-practices/).
- The first time, the GPS can take up to 5 minutes to find your position.
- To mark a DIP, stand at the landing point for the most accurate distance on jump run.

### Delete Marker

Deletes the marker. If it was the active DIP or HARP, that setting is cleared.

## Setting the Active DIP and HARP

Open the marker, and select **Active DIP** or **Active HARP**. The change takes effect immediately, without Save.

- One marker can be the active DIP and one the active HARP at the same time. The same marker can be both.
- Setting a new DIP or HARP replaces the old one.
- Save a new marker before you set it as the DIP or HARP.
- A firmware update clears the active DIP and HARP. The Stratos keeps the marker list.
